Home > Information Directory > CPS University > Terminology 101
CPS University | Terminology 101
CPSU: Learn more about styles, types, materials, and terms
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
AUTOCLAVING STERILIZATION
A process that sterilizes items, supplies, and equipment by subjecting them to high pressure steam at 250° F (121° C) or more. Due to the high damp heat, some plastics cannot be sterilized by autoclaving because they will melt. Other sterilization methods can be used for these plastics. See Sterilization.
Return to top
BOROSILICATE GLASS
This formulation of glass has a high silicate content and at least 5% boron oxide. Pyrex® is a common borosilicate glass. Borosilicate glass is much more resistant the thermal shock (hot and cold temperatures) than any other common glass. See Glass.
Return to top
EXTRUSION BLOW MOLDING
A molding process by which heat-softened resin pellets are forced into a hollow tube-like shape. While soft, a mold closes around the soft tube, pinching the base and top closed. The tube is now capsule-shaped. A tube is then pierced through one end of the capsule and inflates the capsule to take the shape of the enclosing mold. See Mold Seam and Injection Blow Molding.
Return to top
F-STYLE
F-style is a container that usually has a handle, is either square or oblong in shape, with an opening offset from the center.
Common uses: antifreeze bottles, liquid laundry detergent bottles, liquid dishwashing containers
View all F-Style products at CPS
Return to top
F217
A type of foam liner made of PE found in caps and lids.
View all F217 products at CPS
Return to top
F217&PS
A type of liner made of polyethylene (PE) and polystyrene (PS)
View all F217 and PS products at CPS
Return to top
FIBER
A paper based product. The interior of fiber drums is typically treated to hold liquid or dry products.
View all fiber products at CPS
Return to top
FINISH
The part of a bottle that hold the cap, stopper, or closure. The area that has the threads or thread finish. A bottle and its corresponding cap(s) must have a matching finish or neck finish. A 53-400 bottle must be fitted with a 53-400 closure. The first number (in this example: 53) refers to the nominal diameter measured across the inside of the cap at the opening in milimeters. The second number, 400, refers to a specific thread style.
Return to top
FLAME TREATED
Bathing the plastic container in an open flame to promote the oxidation of the surface so that it is receptive to inks, lacquers, paints, and adhesives.
Return to top
FLOURINATION
A treatment for plastic containers that prevents container paneling and distortion and reduces odor emission and chemical permeation. Also reduces flavor or fragrance loss. Some products that use fluorinated bottles include: acetone, auto additives, lighter fluids, degreasers, health and beauty care products, insecticides, kerosene, lubricants, paint thinners, plant food products, waxes, cleaners, polishes, weed killers, herbicides, wood preservatives. See Paneling.
Return to top
FOAM/FOIL
A type of pressure sensitive liner. When placed in the matching lid, and screwed onto the matching container, this liner provides a tamper-evident seal on the container. Subsquently, the lid can be unscrewed from the container, but the liner must be peeled off.
View all foam/foil products at CPS
Return to top
GLASS
The most common form of glass (soda-lime glass) is a manufactured material formed when a mixture of sand, soda, and lime is heated to a high temperature and assumes a molten, or liquid, state. Glass is impermeable and nonporous; keeping product sanitary and tamper-evident. Glass that contains boron oxide is called borosilicate glass. See Borosilicate Glass.
Return to top
HDPE
High-density polyethylene. HPDE is made from hydrocarbons found in petroleum. HDPE is flexible yet more rigid, has a stronger intermolecular force and tensile strength than low-density polyethylene (LDPE). It is also harder and more opaque and can withstand somewhat higher temperatures: 120 °C for short periods, 110 °C continuously. HDPE has a good impact strength, a good resistance to stress crack, chemicals and vapors. However, HDPE is a poor gas barrier. Its natural color is milky white and semi translucent depending on its density. Its SPI resin identification code number is 2.
Common uses: milk jugs, distilled water, large vinegar bottles, grocery bags, liquid laundry and dish detergent, fabric softener, motor oil, antifreeze, bleach and lotion
View all HDPE products at CPS
View a plastics comparison chart at Plasticology 101
Disclaimer: test your product
Return to top
HIS
Heat Induction Seal
A heat induction seal is a lid liner that contains a metallic disk that hermetically seals the top of plastic and glass containers. This is a non-contact process that takes place after the container has been filled and capped. An induction sealing machine is necessary to make the HIS liner adhere to the container neck.
View all HIS closures at CPS
Return to top
INJECTION BLOW MOLDING
A molding process by which resin pellets are heat softened and fed into a mold cavity to create a preform (a test tube shaped container with neck threads). This preform is then transferred to a blow mold (or cavity) where air is blown into the preform to create the shape of the blow mold. See Mold Seam and Extrusion Blow Molding.
Return to top
LDPE
Low-density polyethylene. LDPE is made from hydrocarbons found in petroleum. Its tensile strength and density is lower, but its resilience is higher than high-density polyethylene (HDPE). LDPE is very flexible and has a natural milky color and is translucent. LDPE has high impact strength, a good chemical resistance, and acts as a good barrier for water and alcohol. LDPE, however, is a poor gas barrier. It can withstand temperatures of 80 °C continuously and 95 °C for a short time. It can be translucent or opaque, is flexible, tough, and almost unbreakable. Its SPI resin identification code number is 4.
Common uses: dry-cleaning bags, produce bags, trash can liners, food storage containers, squeezable products
View all LDPE products at CPS
View a plastics comparison chart at Plasticology 101
Disclaimer: test your product
Return to top
MDPE
Medium Density Polyethylene
Medium density polyethylene is less dense than HDPE (high density polyethylene) and more dense that LDPE (low density polyethylene).
View all MDPE products at CPS
Return to top
METAL
Most metal products offered by Container & Packaging Supply are made of tin or aluminium. Both tin and aluminium are resistant to oxidation (rusting) and corrosion.
View all metal products at CPS
Return to top
MOLD SEAM
Plastic bottles will have two lines directly across from each other which is formed at the point of contact of the two mold halves.
Return to top
NICKEL PLATED
Nickel is a silvery white metal that takes on a high polish. Because of its permanence in air and its inertness to oxidation, it is used to coat other metals. It is magnetic, and valuable for the alloys it forms, particularly stainless steel.
View all nickel-plated products at CPS
Return to top
PANELING
Distortion of a plastic container that occurs during aging or storage, caused by the development of a reduced pressure inside the container. Paneling can be reduced by fluorinating the container prior to filling. See Fluorination.
Return to top
PAPER
Paper that is recyclable and biodegradable, used for decorative and practical packaging.
View all paper products at CPS
Return to top
PAPERBOARD
Often called corrugated fiberboard or cardboard, although cardboard might be any heavy paper-pulp based board. Paperboard is a paper-based material consisting of a fluted corrugated sheet and one or two flat linerboards. It is widely used in the manufacture of corrugated boxes (cardboard boxes) and shipping containers.
View all paperboard products at CPS
Return to top
PET
Polyethylene terephthalate. PET or PETE is of the polyester family and is used in beverage, food and other liquid containers. PET can be semi-rigid to rigid and is very lightweight. It acts as a good barrier to alcohol (requires additional "Barrier" treatment) and solvents. PET also has a good gas barrier and a fair moisture barrier. It is not good for strong bases or strong acids, however. It is strong, impact-resistant, and naturally colorless and transparent. PET has good stress crack and impact resistance at room temperature and above. Its SPI resin identification code number is 1. See phthalates.
Common uses: soft drink bottles, cooking oil bottles, peanut butter jars, products containing essential oils, some fruit juices, alcohol beverage bottles, space blankets, ketchup bottles, wine
View all PET products at CPS
View a plastics comparison chart at Plasticology 101
Disclaimer: test your product
Return to top
PHENOLIC
A group of thermosetting resins usually compression molded. Phenolic has good strength and toughness, good arc resistance and other electrical properties, good resistance to solvents and high temperatures, and is bargain-priced.
View all phenolic products at CPS
Return to top
PHTHALATES
Phthalates are a plasticizer, a plastic additive that increases flexibility, transparency, durability, and longevity. There are hundreds of types of phthalates. Orthophthalates are often used to soften PVC (poly vinyl chloride) and are being phased out of many products due to health concerns. Terephthalates, however are added to polyethelyne to create PET (poly ethylene terephthalate), which is not health hazardous. See PET.
Return to top
PLASTIC
Plastics are made of hydrocarbons, typically derived from petroleum or natural gas. Crude oil or petroleum is a fossil fuel (i.e. Coal, petroleum and natural gas), which means it was made naturally from decaying plants and animals. Petroleum contains hydrocarbons, which are molecules containing hydrogen and carbon. Chemically cross-linking different hydrocarbon chains can create plastics, rubber, auto gasoline, diesel fuel, paraffin wax and more. There are two types of plastics: thermoplastics and thermosets. See thermoplastics and thermosets.
Return to top
PLASTISOL
Plastisol is a vinyl material placed on the sealing surface of a metal closure. When plastisol lined caps are placed on their compatible containers, the heated plastisol liner solidifies, creating a seal between.
View all plastisol products at CPS
Return to top
POLYCONE
Polycone
The item has a securely mounted polyethylene cone-shaped liner which offers a two part seal. The closure forms a seal around the rim and the polycone forms a seal against the inner diameter of the container opening.
View all polycone products at CPS
Return to top
POLYETHYLENE
Polyethylene
A type of plastic resistant to water, acids, alkalis, and most solvents. It's classifications range in density: low (LDPE), medium (MDPE) and high (HDPE).
Common uses: shower curtains, unbreakable bottles, pipes, pails, large drums, drinking glasses, insulation for wire and cable
View all PE products at CPS
View all PE products at CPS
View plastics comparison chart
Disclaimer: test your product
Return to top
PP
Polypropylene. PP is often used for food packaging. It is not as tough as HDPE, but it is less brittle. PP is less flexible than LDPE, somewhat stiffer than other plastics, reasonably economical, and can be translucent, opaque, or of any color. Its natural color is opaque, natural grayish-yellow. PP has very good resistance to fatigue, stress crack, and impact. PP is an excellent moisture barrier, a good alcohol and oil barrier, but poor gas barrier. PP has a melting point of 320 °F (160 °C). Food containers will not melt in the dishwasher or during industrial hot filling processes. Its SPI resin identification code number is 5.
Common uses: bottle caps, drinking straws, hinged containers, battery cases, dairy tubs (e.g. sour cream, cottage cheese), cereal box liners
View all PP products at CPS
View a plastics comparison chart at Plasticology 101
Disclaimer: test your product
Return to top
PPE
Polyphenyl ether (PPE), also known as polyphenylene and polyphenylene oxide (PPO), is a type of polyether. The most common form of PPE is a plastic resin. PPE is compatible with polystyrene (PS) and is blended with PS over a wide range of ratios.
View all PPE products at CPS
Return to top
PS
Polystyrene. PS is made from petroleum. Pure solid polystyrene is a colorless, rigid plastic with limited flexibility. It can be cast into molds with fine detail. Polystyrene can be transparent or can be made to take on various colors. I has a good resistance to inorganic chemicals. It is light and heat stable and nontoxic. It has poor impact and stress crack resistance and poor barrier properties. Its SPI resin identification code number is 6.
Common uses: bottle caps, drinking straws
View all PS products at CPS
View a plastics comparison chart at Plasticology 101
Disclaimer: test your product
Return to top
PS Liner
A type of pressure sensitive liner. When placed in the matching lid, and screwed onto the matching container, this liner provides a tamper-evident seal on the container. Subsequently, the lid can be unscrewed from the container, but the liner must be peeled off.
View all PS Liner products at CPS
Return to top
PVC
Polyvinyl chloride
PVC is a widely used thermoplastic polymer. It can be made softer and more flexible by the addition of plasticizers, the most widely used being phthalates.
Common uses: plastic pipes, outdoor furniture, shrink-wrap, water bottles, salad dressing containers, liquid detergent containers
View all PVC products at CPS
View plastics comparison chart
Disclaimer: test your product
Return to top
PVLF
Pulp and Vinyl Lubricated Finish
This vented liner allows air and/or gasses to pass through to prevent the container from swelling, paneling, or leaking.
View all PVLF products at CPS
Return to top
RECYCLING
Plastic and glass can be recycled. Most plastic containers have an SPI resin identification code on them. Inside this logo is a number that informs the consumer what material the container was made from (1-7). All plastics fixed with these codes inform the consumer on which recycling streams these items should be discarded. Recycling for all plastic products may not be available in all areas. Most household glass containers are manufactured from a soda-lime glass formulation. All soda-lime glass can be recycled. Borosilicate glass must not be mixed and recycled with soda-lime glass. Again, recycling for all products may not be available in all areas.
Return to top
RUBBER
An elastic material obtained from the latex of various plants (e.g. the rubber tree) and then treated and modified into various products.
View all rubber products at CPS
Return to top
SFYP
Sealed for your protection
An SFYP liner is a pressure sensitive liner and usually has "Sealed For Your Protection" printed on it.
View all SFYP products at CPS
Return to top
STEEL
Steel is an alloy consisting mostly of iron and partly of carbon. All steel pails are coated with a thin phenolic layer.
View all steel products at CPS
Return to top
STERILIZATION
The process of killing microorganisms to make a container or cap safe to fill. There are three basic approaches used to sterilize plastics. Ethylene Oxide (EtO), Autoclave, and Gamma Radiation. Tests should always be run on plastics to determine which method is most suitable. Not all plastics can and should be sterilized by the same method. See Autoclaving Sterilization.
Return to top
THERMOPLASTICS
There are two types of plastics: thermoplastics and thermosets. Thermoplastics will repeatedly soften when heated and harden when cooled. Some examples of thermoplastics are the resins: polyethylene (HDPE, LDPE, PE, MDPE, PET), polypropylene (PP), and polyvinylchloride (PVC). See Plastic and Thermosets or read more about thermoplastics.
Return to top
THERMOSETS
There are two types of plastics: thermoplastics and thermosets. Thermosets keep their shape at high temperatures, although they will char. Some examples of thermosets include: polyurethanes (mattresses, insulation, toys), unsaturated polyesters (varnishes, furniture, boats), and epoxies (glues, coating for electrical circuits, helicopter blades). See Plastic and Thermoplastics or read more about thermosets.
Return to top
UREA
Urea-formaldehyde or Urea-methanal is a transparent plastic, made from urea and formaldehyde heated in the presence of a mild base such as ammonia or pyridine. Urea's attributes include high tensile strength, low water absorption, high surface hardness, elongation at break, and volume resistance.
Common uses: adhesives, finishes, and molded objects
View all urea products at CPS
View all PE products at CPS
View plastics comparison chart
Disclaimer: test your product
Return to top
